Geyserwise PV Solar Geyser Conversion Kit 100L DC Only

*This kit does not include AC Controllers and is for DC Use Only (Solar Only).

Geyserwise has developed a revolutionary solar geyser system that is not only more efficient than conventional solar geysers but can be installed in less than half the time it would take to install a split pumped solar system with a traditional flat plate or evacuated tubes collector. Also, the initial capital layout is less than half that of a conventional solar geyser.

This system uses a PTC (Positive Temperature Co-efficient) dual AC and DC Stainless steel element expected to last in the region of 10 years. It has been proven that even with the AC back upon, this element is up to 30% more efficient than an electric immersion heating element.

This system makes for easy conversion of literally any existing electrical geyser out there, to solar. It uses PV technology with the use of a specifically designed MPPT (maximum power point tracker) to maximize the output of your PV panels/solar panels to the element.

Real-time system performance is monitored on the system controller display which can be installed anywhere in your home that suits your needs, from this controller you can set the AC backup timer, set the maximum water temperatures and set your geyser to holiday mode if you will be away for a couple of days.

One of the most important factors consumers can benefit from include that the installation of this system does not void your geyser warranties by the manufacturer. The system has been approved by the likes of Kwikot, Heat Tech, Duratherm, and many more. It might be equally important to note that this system is SABS approved.

The SABS certificate and letters from other geyser manufacturers can be downloaded from the specifications tab.

There are kits available from 100Litres to 200Litres with both AC & DC Power supply. However, for 50Litre geysers, the standard dual function element does not fit inside the geyser and therefore only the 1100w DC Element can be installed on these geysers. (See this element in the "accessories" tab. Or clickhere.

Below is a list of all the components typically included with a kit, we provide the option to buy these kits with no panels.

(Please note that the system has to be independently connected to the number of panels as outlined per kit below.*)
Important Note: Roof Hook Brackets not included (this is required for tile roof installations) - see Accessories Tab Typical Tile roof hook bracket installation

• 100L PV Kits - 4 roof hook mounts required*
• 150L PV Kits - 6 roof hook mounts required*
• 200L PV Kits - 8 roof hook mounts required*

The 100L kit is made up of the following components. 

1.5 kW AC/DC Withdrawable Element x1

Flange if required (Flange is used on Heat Tech and Kwikott Geysers)

PTC Stainless Steel  Sensor Tube x1

ECO MPPT x1

Anderson Connector x1

Inline Fuse holder x1

30A Fuse x1

Element Connector Cable x1

Watch: PV System Installation video

Note from the Manufacturer

• It is important to understand the limitations of the MPPT and the size and amount of PV panels that can be connected to the MPPT
  • Limitation 1: Input voltage of 138 VOC (on average) Maximum 150 VOC
    • 3X270W PV Panels in Series = 38.7 VOC X3 = 116.1 (well withing the voltage specified)
    • 3X330W PV Panels in Series = 138.6 VOC X3  = 138.6 (this is also fine for average operation)
    • 3 LARGER PANELS OR HIGH VOLTAGE PANELS SHOULD NOT BE CONNECTED IN SERIES
    • ALL OUR DIAGRAMMES SPECIFY THE HIGHEST SIZE AS 335W AND INSTALLERS SHOULD STICK TO THIS
    • IF MORE PANELS ARE REQUIRED THE PANELS CAN BE PUT 2 in SERIES, 2 in SERIES THEN PARALLEL. BUT REMEMBER THERE ARE LIMITATIONS ON THE OUTPUT AMPERE AS WELL, SO THE VOLTAGE ALONE SHOULD NOT BE USED TO MAKE THE CALCULATION. THE OUTPUT AMPERE SHOULD BE TAKEN INTO ACCOUNT AS WELL.

• • Limitation 2:  the load: The element is only rated at 900W on average (MAXIMUM 1200W). Any excess energy connected to the MPPT cannot be used by the load. The MPPT would have to get rid of this energy somehow. For example, if 1600W is connected to the MPPT and PV panels are producing 1600W, but the element can only use 1200W of energy. Somehow the MPPT would need to absorb an extra 400W.
    • Consequence: MPPT will run at higher temperatures than what it should
    • Components will be put under severe
    • It is important to stick to the Maximum 1200W PV Panels to be connected to the MPPT
    • PLEASE MAKE ALL INSTALLERS AWARE OF THIS AS MANY INSTALLERS ARE CONNECTED TOO MANY PANELS (IN TERMS OF TOTAL WATTAGE) TO THE SYSTEM AND NEITHER THE MPPT OR ELEMENT IS DESIGNED FOR THIS. IT IS NOT APPROPRIATE TO CONNECT 4x410W PANELS ON THE SYSTEM. IT DOES NOT MATTER IN WHAT CONFIGURATIONS YOU CONNECT THE PV PANELS
    • OUR DIAGRAMMES ARE VERY CLEAR ON WHAT COMBINATIONS OF PV PANELS ARE ALLOWED
    • WITH ANY RETURNS – PLEASE CONFIRM THE CONFIGURATION AND AMOUNT OF PV PANELS – WE WILL NOT EXCHANGE UNITS THAT HAVE NOT BEEN CONNECTED PROPERLY.
    • We can try and repair these units, but the same will happen again if the number of PV panels are not reduced

• • Limitation 3: Maximum output Amps: 25A (per attached sheet)

It is important to understand that if the PV panels are connected in parallel that the input Current increases (compared to the series connection). For example, two series, so series then parallel on 270W or 330W PV panels will give you an input current in the region of 16A to 18 A. For a series connection, the input current will be in the region of 8A and 9A for 270 W PV panels and 330W PV Panels.

As per the picture below, the job of the MPPT is to ensure that theoutput volage matches theload voltage. In our case, the load voltage is between 48V and 72V. If the voltage is reduced, the output current must increase.